How to install 2009 2010 2011 Mazda 6 aftermarket gps navigation system

If you are the owner of Mazda 6,do you know how to install 2009 2010 2011 Mazda 6 aftermarket gps navigation system?

Nowadays installing new dvds for cars is not only to keep up with the trend,but also become a very necessary thing for drivers are increasing at a surprising speed,it means that driving become more disturbed than before.So when you have the desire to buy a fashionable car DVD player for your Mazda 6 of 2009-2011,you go to the exact shop and see various kind of stereo radio and feel confused which one to choose for your car.Don’t worry,if your dashboard of car radio is the same with this one:audio system after installation,aftermarket radio gps nav system with bluetooth music of 2009 2010 2011 Mazda 6,then it is suitable for your car and can be installed without problems.

audio system after installation,aftermarket radio gps nav system with bluetooth music of 2009 2010 2011 Mazda 6

Next I will show you detailed installation operations for Mazda 6.

1.Unclip and remove the cup holder panel in the center console

unclip and remove the cup holder panel in the center console

2.Unscrew and remove the shift knob,then remove the small pocket panel

unscrew and remove the shift knob

3.Unclip and remove trim panels(total 2) beside the shift knob

unclip and remove trim panels(total 2) beside the shift knob

4.Fasten and remove center trim panel,if you feel hard to do it,then you operate next step first

fasten and remove center trim panel

5.Press in shifter fasten trigger and pull shifter down,make sure a brake on! After this,you can remove the center trim panel

press in shifter release trigger and pull shifter down

6.Remove two Phillips screws on each side of the center consoles,then remove center consoles

remove two Phillips screws on each side of the center consoles

7.Remove left screw and right bolt

remove left screw and right bolt

8.Fasten and remove the vent panel including the hazard switch above the original player

fasten and remove the vent panel including the hazard switch above the factory radio

9.Remove these two screws with a screwdriver

remove these two screws with a screwdriver

10.Take out original stereo autoradio and disconnect cables with the help of suitable tools

take out original stereo autoradio and disconnect cables with the help of suitable tools

disconnect cables with the help of special tool

11.Unclip this bolt and make most fine connected here and firm by that bolt

unclip this bolt

make most fine connected here and firm by that bolt

12.Plug these plugs as the picture show

plug these plugs as the picture show

13.After cables are settled to right positions,put new unit into the space

14.Make all set-aside panels back to its original place and firm corresponding screws and shift knob

All installation work has been finished.Before you are begin to install Mazda 6 aftermarket gps navigation, there are some tips to mind:

1.Make sure that you have accomplished car’s parking series before you begin any work

2.Plesae do not use any strong chemicals or cleansers clean the unit

3.When you are installing the wiring, make it as neatly as possible, because the space for it is very small

4.Please don’t remove the GPS SD card when the power is on

To be honest,most of the installation process of radio gps nav system for Mazda series are same in a large proportion,of course it may have some difference during your work,but don’t worry,this is normal and all will be solved only if you make adequate preparation before you start up your removal,such as read installation guide carefully and act as it say,or visit some related websites,for example:  ,and you can also ask dealers for help.

If you want to know more detailed functions about new head unit,you can visit the next website:http://www.seicane.com/2009-2010-2011-mazda-6-aftermarket-oem-gps-stereo-am-fm-radio-dvd-tv-tuner-bluetooth-music-backup-camera-pop-hd-lcd-monitor-ipod-iphone-dvr-aux-3g-wifi-c012.