A step-by-step installation guide for a Toyota Land Crusier 100 car stereo before 2004 with Capacitive Touch Screen Bluetooth AX USB SD 3G WiFi Video GPS Navigation system

Some car owners may think that to install a new car stereo is quite bothering. In fact, it’ s just a job of about half an hour, which consists of the removal of your old radio and the installation of a new radio. If you have a Toyota Land Crusier 100 before 2004, then you can refer to this Toyota Land Crusier 100 car stereo before 2004 installation guide. And the effect picture will be like as below, which is a Toyota Land Crusier 100 car stereo before 2004 after installation from Seicane.

Toyota Land Crusier 100 car stereo before 2004 after installation

Toyota Land Crusier 100 car stereo before 2004 after installation

 

Precautions for this installation:

1.Before you start up any work, park your car well and unplug the negative power cable to avoid any danger.

2.Please make sure that all fastened wires are isolated with electrical tape.

3.Please make sure the ignition is off to avoid short circuit.

 

Toyota Land Crusier 100 car stereo before 2004 installation guide

1.Take out the two blots that distributed on both sides of handbrake.

1.Take out the two blots that distributed on both sides of handbrake

1.Take out the two blots that distributed on both sides of handbrake

 

2.Remove screws with your hand.

2.Remove screws with your hand

2.Remove screws with your hand

 

3.After the bolts are removed, take out the left and right loosed dashboard.

3.After the bolts are removed, take out the left and right loosed dashboard

3.After the bolts are removed, take out the left and right loosed dashboard

 

4.Disconnect the cable between them.

4.Disconnect the cable between them

4.Disconnect the cable between them

 

5.Get out the screw with your hands.

5.Get out the screw with your hands

5.Get out the screw with your hands

 

6.Remove five screws as the picture show.

6.Remove five screws as the picture show

6.Remove five screws as the picture show

 

7.Pull the original radio out of the dashboard.

7.Pull the original radio out of the dashboard

7.Pull the original radio out of the dashboard

 

8.Disconnect the connectors at the back of the original radio.

8.Disconnect the connectors at the back of the original radio

8.Disconnect the connectors at the back of the original radio

 

9.Connect the cables on the new Seicane stereo as the user manual shows and place them well.

10.Put the new Seicane stereo into the dash.

11.Turn on the new Seicane stereo and have a comprehensive check if it works well.

12.Install 4 screws back to their original position.

13.Check whether the unit is working without problem.

14.If everything is OK, make trim panel back on your new Seicane stereo.

Now you may probably have a general idea about how to install a new stereo in your Toyota Land Crusier 100 before 2004. If you have any questions, please don’t hesitate to consult your dealer or professional. Please make sure you are clear about every step before the installation. Some of you may don’t find an ideal stereo for your car, you are welcome to check out this intelligent Toyota Land Crusier 100 car stereo before 2004 from Seicane, please click for more details:

 

http://www.seicane.com/10-1-inch-toyota-land-crusier-100-before-2004-android-capacitive-touch-screen-radio-gps-navigation-system-with-bluetooth-tpms-dvr-obd-ii-rear-camera-aux-usb-sd-3g-wifi-steering-wheel-control-video-s082760

 

This remarkable Toyota Land Crusier 100 car stereo comes with the latest GPS navigation system to provide lane assist, landmark display, 3D street view, route planning, turn-by-turn direction and voice prompts can guide you to your desired destination within the least time. With built-in Bluetooth technology, you can easily link with your enabled mobile phone for hands-free calls and streaming music to relax both you and your passengers along the way.

This entry was posted in Toyota car stereo and tagged . Bookmark the permalink.

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>