Concise Removal and Installation Steps for a 2012 2013 2014 2015 Skoda OCTAVIA Car Radio with GPS Bluetooth Function

Can you believe that with a detailed installation guide for a car radio, you can also try to remove your factory radio and install a new aftermarket car radio? If you are a car owner of 2012 2013 2014 2015 Skoda OCTAVIA who is also looking for a correct car radio installation guide, then I would like to congratulate that you’ve found it. The following is a 2012 2013 2014 2015 Skoda OCTAVIA car radio installation guide from Seicane which can be taken as your reference. Wish it is helpful for you.

2012 2013 2014 2015 Skoda OCTAVIA car radio after installation

2012 2013 2014 2015 Skoda OCTAVIA car radio after installation

Before and during installation, you should notice:

1.Before connecting, please make sure the ignition is off to avoid short circuit.

2.Ensure connect the yellow and red power cable at last.

3.Ensure that all loose wires are isolated with electrical tape

4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5.Ensure that all ground is connected to the same place.

6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

2012 2013 2014 2015 Skoda OCTAVIA car radio installation guide

1. Remove the trim panel with a plastic removal tool.

Remove the trim panel with a plastic removal tool

Remove the trim panel with a plastic removal tool

1-1

1-1

2. Remove four screws that fixed the radio on the dashboard.

Remove four screws that fixed the radio on the dashboard

Remove four screws that fixed the radio on the dashboard

3. Softly release the original radio and take it out.

Softly release the original radio and take it out

Softly release the original radio and take it out

4. Unplug the connectors and cables at the back of the original radio.

Unplug the connectors and cables at the back of the original radio

Unplug the connectors and cables at the back of the original radio

5. Check all the accessories for the new Seicane car radio.

6. Connect the harnesses to the back of the new Seicane car radio.

7. Connect the Seicane car radio to your original stereo’s plugs.

8. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

9. Put the new Seicane car radio into the dash.

10. Put everything into their original place. All the installation is done.

 

Now do you know how to install a new car radio for a 2012 2013 2014 2015 Skoda OCTAVIA? If you meet any problems and cannot solve them individually, you can seek help from your dealer, someone experienced or a professional. And you can also directly ask a professional technician for help. To select an ideal car radio, if you have no ideas, here I would like to share an amazing 2012 2013 2014 2015 Skoda OCTAVIA car radio from Seicane with you. Here comes the link, please click:

https://www.seicane.com/hd-touchscreen-2012-2015-skoda-octavia-android-radio-gps-navigation-system-with-bluetooth-obd2-dvr-rearview-camera-tv-1080p-4g-wifi-steering-wheel-control-s18v214

This car radio is loaded with the most advanced and stable Android 7.1 operation system and a powerful quad-core 1.6 GHz RK PX3 CPU processor, which will greatly facilitate its operation. Thus, it can be taken into your consideration when you plan to replace your factory radio.

The worldwide real-time GPS navigation system is specially built in this unit for you to easily locate where you are and find the right way to reach anywhere you would like to go to according to turn-by-turn directions and voice prompts.

Additionally, through the Bluetooth connection between your Bluetooth-enabled mobile phone and this unit, both hands-free calls and streaming music are both available for you to gain a lot of convenience and enjoyment.

Wish you like this unit and good luck to you!

Posted in Uncategorized | Tagged | Leave a comment

How to Upgrade a 2006 2007 Mitsubishi Raider GPS Bluetooth Radio Stereo Head Unit Perfectly

What specific information should you know when you want to get a suitable car radio for your car? Actually, with knowing your car model, manufacturing year and the measurement, you can easily search online and find an ideal car radio for your beloved car. After getting the radio, you need to find a correct installation guide to help with the installation. Today I’d like to share several steps about how to upgrade a 2006 2007 Mitsubishi Raider gps bluetooth radio by installing a brand new one from Seicane. Wish you can learn something from these steps.

2006 2007 Mitsubishi Raider GPS Bluetooth Radio Stereo after installation

2006 2007 Mitsubishi Raider GPS Bluetooth Radio Stereo after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details:http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2006 2007 Mitsubishi Raider car radio installation steps

1. Loosen the trim panel with a lever.

Loosen the trim panel with a lever

Loosen the trim panel with a lever

2. Take the panel off the dash and disconnect the wires from the car.

Take the panel off the dash and disconnect the wires from the car

Take the panel off the dash and disconnect the wires from the car

2-1

2-1

3. Remove the four screws which are holding the unit with a screwdriver.

Remove the four screws which are holding the unit with a screwdriver

Remove the four screws which are holding the unit with a screwdriver

4. Take out the unit and disconnect the wire harness at the back of the unit.

Take out the unit and disconnect the wire harness at the back of the unit

Take out the unit and disconnect the wire harness at the back of the unit

5. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

6. Connect the Seicane car radio to your original car radio’s plugs.

Connect the Seicane car radio to your original car radio's plugs

Connect the Seicane car radio to your original car radio’s plugs

7. Put the new Seicane car radio into the dash.

8. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

9. Put trim panel back on your new Seicane car radio after the normal test.

 

It is natural if you come across any problems during the installation process. We suggest you contact your dealer for seeking a wiring diagram. Or you can turn to a professional and someone experienced for help. To purchase an ideal car radio for your beloved car, you might refer to a 2006 2007 Mitsubishi Raider gps bluetooth car radio from Seicane. Here comes the link, please click:

http://www.seicane.com/in-dash-autoradio-gps-navigation-bluetooth-for-2006-2007-mitsubishi-raider-with-dvd-tv-tuner-aux-ipod-mp3-steering-wheel-control-dual-zone-sd-usb-t6015

This in-dash car radio designed for 2006 2007 Mitsubishi Raider can greatly facilitate its operation and offer users higher configuration as it is running with the newest WinCE6.0 operation system and has a powerful Cortex A9 1GHz dual-core CPU.

You can not only build a comfortable and convenient car interior environment but also gain a brand new driving experience because of a wide range of compatible features, which include built-in GPS function, FM/AM radio, DVD player, Bluetooth hands-free phone calling, Bluetooth streaming music, iPod &iPhone connection, USB& SD connection, dual zone function, etc.

Apart from the above features I mentioned, there are also two optional functions can be added to this unit, consist of digital TV and rearview camera.

Just take this radio, get it installed in your beloved car and enjoy your relaxing trip from now on!

Posted in Uncategorized | Tagged | Leave a comment

A Concise Guide on a 2008 2009 2010 2011 2012-2014 Toyota Corolla Car Radio Removal and Installation with USB Audio Bluetooth Function

Are you fed up with your old outdated car radio since it is not modern enough for you to get access to modern features? Do you want to gain more convenience and enjoyment in your beloved car? If your answers towards these features are both “yes”, then you can consider replacing your factory radio with a new aftermarket car radio. As for the installation, I’d like to share a 2008 2009 2010 2011 2012-2014 Toyota Corolla car radio installation guide from Seicane with you. If you happen to have the same car model, you can refer to this installation guide carefully.

2008 2009 2010 2011 2012-2014 Toyota Corolla Car Radio after installation

2008 2009 2010 2011 2012-2014 Toyota Corolla Car Radio after installation

Tips about the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2008 2009 2010 2011 2012-2014 Toyota Corolla car radio installation guide

1. Remove the bottom panel (air conditioning) with plastic knife.

Remove the bottom panel (air conditioning) with plastic knife

Remove the bottom panel (air conditioning) with plastic knife

2. Pry the top of the original car CD panel with plastic knife.

Pry the top of the original car CD panel with plastic knife

Pry the top of the original car CD panel with plastic knife

3. Remove the four screws with a screwdriver.

Remove the four screws with a screwdriver

Remove the four screws with a screwdriver

4. Take the original radio out of the dash.

Take the original radio out of the dash

Take the original radio out of the dash

5. Pull the plug of the original radio.

Pull the plug of the original radio

Pull the plug of the original radio

6. Socket docking with the original radio directly, instead of cutting the original plug off.

Socket docking with the original radio directly, instead of cutting the original plug off

Socket docking with the original radio directly, instead of cutting the original plug off

7. Put the original radio plug into our Seicane radio.

Put the original radio plug into our Seicane radio

Put the original radio plug into our Seicane radio

8. Put the new Seicane radio back into the dash.

9. Turn on the new Seicane radio to check if all functions work well. If it doesn’t, please check whether all the cables are connected correctly.

10. Install four screws and panels into their original place.

 

Wish the above installation guide can be helpful for you. Don’t worry if you encounter any difficulties. To overcome these difficulties, you may consult your dealer, communicate with someone experienced or turn to a professional. If you still think the installation instruction is too hard, you can directly arrange a professional technician to help you install the new car radio.

Besides, it is very essential for you to select an ideal car radio. If you have no ideas, here I would like to share a great 2008 2009 2010 2011 2012-2014 Toyota Corolla car radio from Seicane with you. For more details, please click:

https://www.seicane.com/2-din-dvd-player-car-radio-android-gps-navi-stereo-for-2008-2014-toyota-corolla-bluetooth-support-dvr-dab-backup-camera-usb-wifi-digital-tv-1080p-mirror-link-s32749f

Upgraded to the latest firmware and software, this amazing car radio specific for 2008 2009 2010 2011 2012-2014 Toyota Corolla is based on the advanced Android 7.1.1 operation system and a strong quad-core CPU processor to enhance its capabilities and performance. So with it installed in your car, your driving experience will be taken up a notch.

With the assistance of turn-by-turn direction and voice prompts provided by the high-end 3D GPS navigation system, you are able to know your current locations and navigate to your desired destinations. And this unit’s dual zone function enables you to freely listen to your favorite music while navigating, which won’t have any negative influence on GPS navigation.

Besides, under the wireless Bluetooth technology, you can connect your Bluetooth-enabled mobile phone to this car radio so as to dial, answer, reject and mute hands-free calls as well as listen to Bluetooth streaming music. Thus you can gain a lot of convenience and enjoyment.

Wish you like this car radio and good luck to you!

Posted in Uncategorized | Tagged | Leave a comment

How to Remove a 2010 2011 Seat Alhambra Factory Radio to Install a Touch Screen Car Radio Navigation System

If you are not satisfied with your factory radio, why not think about replacing it with a new aftermarket car radio? An ideal car radio can be compatible with a wide range of comprehensive features to help enrich your in-car life. The following is a 2010 2011 Seat Alhambra car radio installation instruction from Seicane, which I would like to share with you. If you have the same or similar dashboard, you can refer to this instruction to help with the installation.

2010 2011 Seat Alhambra Factory Radio after installation

2010 2011 Seat Alhambra Factory Radio after installation

Precautions for this installation:

1. Before you start up any work, park your car well and unplug the negative power cable to avoid any danger.

2. Please make sure that all fastened wires are isolated with electrical tape.

3. Please make sure the ignition is off to avoid short circuit.

4. Please prepare a lever and a screwdriver before the removal and the installation.

5. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd- 400

2010 2011 Seat Alhambra car radio installation instruction

1. Remove the top panel with a lever.

Remove the top panel with a lever

Remove the top panel with a lever

2. Disconnect the connector at the back of the panel.

Disconnect the connector at the back of the panel

Disconnect the connector at the back of the panel

3. Unscrew the screw with a screwdriver.

Unscrew the screw with a screwdriver

Unscrew the screw with a screwdriver

4. Remove the metal sheet on the top with your hands.

Remove the metal sheet on the top with your hands

Remove the metal sheet on the top with your hands

5. Unscrew two screws circled in red shown as follows under the metal sheet.

Unscrew two screws circled in red shown as follows under the metal sheet

Unscrew two screws circled in red shown as follows under the metal sheet

6. Remove the air conditioner vent with your hands.

Remove the air conditioner vent with your hands

Remove the air conditioner vent with your hands

7. Unscrew two screws under the vent with a screwdriver.

Unscrew two screws under the vent with a screwdriver

Unscrew two screws under the vent with a screwdriver

8. Remove the panel on the original car radio.

Remove the panel on the original car radio

Remove the panel on the original car radio

9. Unscrew four screws holding the original car radio with a screwdriver.

Unscrew four screws holding the original car radio with a screwdriver

Unscrew four screws holding the original car radio with a screwdriver

10. Take the original car radio out of the dash.

Take the original car radio out of the dash

Take the original car radio out of the dash

11. Disconnect all the connectors at the back of the original car radio.

Disconnect all the connectors at the back of the original car radio

Disconnect all the connectors at the back of the original car radio

12. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

13. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

14. Connect the Seicane car radio to your original car radio’s plugs.

15. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

16. Put the new Seicane car radio into the dash.

17. Put everything into their original place.

 

Before installation, please make clear that you understand every detailed step. If you have any doubts about the radio or the replacement process, please feel free to consult your dealer, communicate with someone experienced or seek help from a professional. Anyway, before installation, it is essential for you to select a ideal car radio for your beloved car. If you don’t know which kind of car radios can fit your car, you can check out the following link for a remarkable 2010 2011 Seat Alhambra car radio from Seicane.

https://www.seicane.com/2010-2011-seat-alhambra-android-gps-navigation-car-dvd-player-with-3g-wifi-mirror-link-backup-camera-obd2-dvr-hd-touch-screen-steering-wheel-control-bluetooth-s6920

Compared with your factory radio with several simple functions, this car radio can support a wide range of practical and entertainment features, mainly including 3D GPS navigation function, FM/AM radio tuner, AUX, file management, steering wheel, USB or SD card connection, etc. Thanks to these features, you will definitely embrace a brand new driving experience.

Through the wireless Bluetooth connection between your Bluetooth-enabled mobile phone and this car radio, you can dial, answer, reject and mute Bluetooth hands-free phone calls as well as freely listen to Bluetooth streaming music from your phone playlists without taking your hands off the steering wheel. By doing so, you can gain a lot of convenience and enjoyment so as to enrich your in-car life.

What are you waiting for? This car radio is at a reasonable price now, just add it to your shopping cart.

Posted in Uncategorized | Tagged | Leave a comment

Quick Tutorial on a 2006 2007 2008 2009 2010-2013 Audi TT GPS Bluetooth Car Radio Upgrading

Would you like to install a multifunctional car radio in your car to replace your factory radio so as to enrich your in-car life? If you have such a plan and would like to finish the whole upgrade process on your own, you can find a related installation guide and follow it to deal with the installation. The following is a 2006 2007 2008 2009 2010-2013 Audi TT car radio installation guide from Seicane which can be taken as reference.

2006 2007 2008 2009 2010-2013 Audi TT GPS Bluetooth Car Radio after installation

2006 2007 2008 2009 2010-2013 Audi TT GPS Bluetooth Car Radio after installation

Some tips before the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2006 2007 2008 2009 2010-2013 Audi TT car radio installation guide

1. The original car radio.

The original car radio

The original car radio

2. Prepare four removal keys.

Prepare four removal keys

Prepare four removal keys

3. There are four removal slots in the radio. Insert the removal keys into the holes of the radio.

There are four removal slots in the radio. Insert the removal keys into the holes of the radio

There are four removal slots in the radio. Insert the removal keys into the holes of the radio

4. Pull outwards to release the radio.

Pull outwards to release the radio

Pull outwards to release the radio

5. Remove the removal keys in the radio.

6. Unplug connectors and cables at the back of the radio.

Unplug connectors and cables at the back of the radio

Unplug connectors and cables at the back of the radio

7. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

8. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

9. Connect the Seicane car radio to your original radio’s plugs.

10. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

11. Put the new Seicane car radio into the dash.

12. Put everything into their original place. All the installation is done.

 

Wish the above installation guide can be helpful for you. If you have any doubts, please feel free to contact your dealer, communicate with someone experienced or turn to a professional for help. For avoiding damage to either your car radio or your car, you can directly go to a car radio upgrade center and ask a professional technician to help you install the new car radio. Anyway, before installation, please do select an ideal car radio. If you have no ideas, here I would like to recommend an amazing 2006 2007 2008 2009 2010-2013 Audi TT car radio from Seicane to you. For more details, please click:

https://www.seicane.com/2006-2013-audi-tt-android-in-dash-radio-dvd-gps-system-with-touch-screen-bluetooth-radio-wifi-mirror-link-obd2-backup-camera-s32525

This car radio is loaded with the latest Android 7.1 operation system, a powerful quad-core CPU processor and 2GB RAM to enhance its capabilities and performance.

Even if y ou are not good at identifying directions, you can gain a lot of help from the advanced 3D GPS navigation system. With it, you can get access to a lot of features, mainly including current location, speed, mileage, landmark building display, 3D street view, destination search and turn-by-turn directions. Thanks to these features,  you can have the best route option and gain the shortcut to reach your destinations. And this unit comes with dual zone function, which enables you to listen to your favorite music while navigating.

Additionally, by simply paring your Bluetooth-enabled mobile phone with this car radio, you can freely dial, answer, reject and mute hands-free phone calls as well as listen to Bluetooth streaming music, which can bring you both convenience and enjoyment.

Wish you like this unit and good luck to you!

Posted in Uncategorized | Tagged | Leave a comment

How to Achieve the Removal and Installation Process of a 2007 2008 2009 2010 2011-2014 Mazda CX-7 GPS Bluetooth Car Radio

Do you have a plan to replace your factory radio with a new aftermarket car radio?If yes, you must be curious about the removal of the factory radio and the installation of a new car radio. This article aims to introduce 2007 2008 2009 2010 2011-2014 Mazda CX-7 car radio removal and installation steps from Seicane to you. If you find your dashboard is similar to or just the same as the image below, just refer to the following guide carefully.

2007 2008 2009 2010 2011-2014 Mazda CX-7 GPS Bluetooth Car Radio after installation

2007 2008 2009 2010 2011-2014 Mazda CX-7 GPS Bluetooth Car Radio after installation

Precautions for this installation:

1. Before you start up any work, park your car well and unplug the negative power cable to avoid any danger.

2. Please make sure that all fastened wires are isolated with electrical tape.

3. Please make sure the ignition is off to avoid short circuit.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2007 2008 2009 2010 2011-2014 Mazda CX-7 car radio installation steps

1. Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside.

Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside

Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside

2. Remove screws that fixed the radio on the dashboard.

Remove screws that fixed the radio on the dashboard

Remove screws that fixed the radio on the dashboard

3. Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio.

Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio

Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio

4. Unplug the connectors at the back of the factory radio.

Unplug the connectors at the back of the factory radio

Unplug the connectors at the back of the factory radio

5. Make antennas and cables connected step by step, and you should be very careful when you are doing this for it will affect whole procedure.

Make antennas and cables connected step by step, and you should be very careful when you are doing this for it will affect whole procedure

Make antennas and cables connected step by step, and you should be very careful when you are doing this for it will affect whole procedure

6. Put the new Seicane radio into your car, you should check whether your connections are correct, and you’d better have a tidy for the cables.

7. If everything is OK, firm screws into their original place.

If everything is OK, firm screws into their original place

If everything is OK, firm screws into their original place

8. Firm the panel on the new Seicane radio. Finally the new Seicane radio is installed and a comprehensive test should be conducted on the new radio.

Firm the panel on the new Seicane radio. Finally the new Seicane radio is installed and a comprehensive test should be conducted on the new radio

Firm the panel on the new Seicane radio. Finally the new Seicane radio is installed and a comprehensive test should be conducted on the new radio

 

Before installation, please make clear every detailed removal and installation step. If you cannot fully understand these steps, please don’t hesitate to seek help from your dealer, someone experienced or a professional. If you still think the installation process is too complicated for you, you’d better go to a car radio upgrade center and have the new car radio installed by a professional technician.

Additionally, it is vital for you to pick an ideal car radio for your beloved car. If you have no ideas,  you can refer to the following link which is an amazing 2007 2008 2009 2010 2011-2014 Mazda CX-7 car radio from Seicane.

https://www.seicane.com/autoradio-android-gps-navigation-system-for-2007-2014-mazda-cx-7-with-dvd-player-mirror-link-multi-touch-screen-obd-dvr-bluetooth-rear-view-camera-tv-usb-sd-3g-wifi-s167007

This excellent car radio’s operation system has been upgraded to the advanced Android 7.1 version and it has a powerful quad-core CPU processor to improve its performance.

It can support a wide range of practical and entertainment features, which mainly include 3D GPS navigation, FM/AM radio tuner, DVD player, Bluetooth hands-free phone calls, Bluetooth streaming music, file management, AUX, file management, etc.

Thanks to the worldwide real-time GPS navigation system of high accuracy, you can quickly know your current locations and find the right way to reach your desired destinations according to turn-by-turn directions and voice prompts provided by the high-end 3D GPS navigation system. What’s more, thanks to this unit’s dual zone function, you can freely listen to radio, USB or SD card music playback under GPS mode, which won’t have negative influence on GPS function.

This car radio is at a competitive price now. If you like it, don’t forget to add it to your shopping cart. Good luck!

Posted in Uncategorized | Tagged | Leave a comment

An Easy Installation Instruction of a 2009 2010 2011 2012 MAZDA 5 Car Radio with Bluetooth GPS Navigation

Would you like to get access to the most advanced and modern features in your car while you are driving? If your answer is yes, then an ideal car radio can meet your different needs. If your factory radio is too old to be compatible with some new features, you can replace it with a new aftermarket car radio. And if you are going to deal with the car radio installation by yourself, you can refer to a related car radio installation instruction. The following is a 2009 2010 2011 2012 MAZDA 5 car radio installation instruction from Seicane, which can be taken as your reference.

2009 2010 2011 2012 Mazda PREMACY Radio after installation

2009 2010 2011 2012 Mazda PREMACY Radio after installation

Tips about the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s therecommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2009 2010 2011 2012 MAZDA 5 car radio installation instruction

1. Unclip and remove the cup holder panel in the center console.

Unclip and remove the cup holder panel in the center console

Unclip and remove the cup holder panel in the center console

1-1

1-1

2. Unclip and remove the small pocket panel on the back of the center console behind shifter.

Unclip and remove the small pocket panel on the back of the center console behind shifter

Unclip and remove the small pocket panel on the back of the center console behind shifter

2-1

2-1

3. Remove two 8mm bolts under the cup holder panel holding the back half of the center console to the front half.

Remove two 8mm bolts under the cup holder panel holding the back half of the center console to the front half

Remove two 8mm bolts under the cup holder panel holding the back half of the center console to the front half

4. Unscrew the shift knob and remove it carefully.

Unscrew the shift knob and remove it carefully

Unscrew the shift knob and remove it carefully

5. Unclip and remove the shifter trim panel.

Unclip and remove the shifter trim panel

Unclip and remove the shifter trim panel

6. Slide both seats forwards and remove two Phillips screws on each side of the center console under the screw covers.

Slide both seats forwards and remove two Phillips screws on each side of the center console under the screw covers

Slide both seats forwards and remove two Phillips screws on each side of the center console under the screw covers

7. Unclip and pull back the panels at the lower front sides of the center console.

Unclip and pull back the panels at the lower front sides of the center console

Unclip and pull back the panels at the lower front sides of the center console

8. Remove two Phillips screws from both sides(total of four) of the front lower half of the center console.

Remove two Phillips screws from both sides(total of four) of the front lower half of the center console

Remove two Phillips screws from both sides(total of four) of the front lower half of the center console

8-1

8-1

9. Unclip and remove the vent panel including the hazard switch above the factory radio. Then it will be much easier for you to get access to the screws. And remove the two screws.

Unclip and remove the vent panel including the hazard switch above the factory radio. Then it will be much easier for you to get access to the screws. And remove the two screws

Unclip and remove the vent panel including the hazard switch above the factory radio. Then it will be much easier for you to get access to the screws. And remove the two screws

9-1

9-1

9-2

9-2

10. Remove two screws from behind the shifter trim.

Remove two screws from behind the shifter trim

Remove two screws from behind the shifter trim

11. Pull center console forward so as to gain access to two screws under the climate controls. And then remove these two screws.

Pull center console forward so as to gain access to two screws under the climate controls. And then remove these two screws

Pull center console forward so as to gain access to two screws under the climate controls. And then remove these two screws

 

 

12. Unclip harness and pull rear center console backwards.

Unclip harness and pull rear center console backwards

Unclip harness and pull rear center console backwards

 

 

13. Press in shifter to release trigger and pull shifter down, make sure to have a brake on.

Press in shifter to release trigger and pull shifter down, make sure to have a brake on

Press in shifter to release trigger and pull shifter down, make sure to have a brake on

 

14. Use a pry tool to release climate controls.

Use a pry tool to release climate controls

Use a pry tool to release climate controls

 

 

15. Remove one screw and one 10mm bolt.

Remove one screw and one 10mm bolt

Remove one screw and one 10mm bolt

 

 

16. Pull factory radio out, release clips and unplug radio connectors.

Pull factory radio out, release clips and unplug radio connectors

Pull factory radio out, release clips and unplug radio connectors

 

 

 

17. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

 

18. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

 

19. Connect the Seicane car radio to your original car radio ‘s plugs.

20. Turn on the new Seicane radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

21. Put the new Seicane radio into the dash.

22. Put everything into their original place. All the installation is done.

 

 

 

 

Wish the above installation guide can be helpful for you to some extent. If you have any problems and don’t know how to deal with, please feel free to contact your dealer, communicate with someone experienced or turn to a professional for help. Or if you still think it hard for you to install the new car radio, you can directly arrange a professional technician to help you deal with the installation.

As for the selection of an ideal car radio, here I would like to share an amazing 2009 2010 2011 2012 MAZDA 5 car radio from Seicane with you. For more details, please click:

 

 

https://www.seicane.com/2009-2012-mazda-5-android-gps-navigation-system-with-dvd-player-radio-mirror-link-multi-touch-screen-obd-dvr-rear-view-camera-tv-3g-wifi-usb-sd-bluetooth-s168005

 

With this car radio installed in your car, you can see that this car radio comes with almost all the main features that you are expecting from a car radio, including 3D GPS navigation system, FM/AM radio tuner, Bluetooth hands-free phone calls, Bluetooth streaming music, DVD player, AUX, file management, etc.

With the assistance of the high-end 3D GPS navigation system, you are able to know where you are and get the right route to reach any locations you would like to go to according to turn-by-turn directions and voice prompts. Additionally, thanks to this unit’s dual zone function, you are able to freely enjoy your favorite music behind the scene under GPS mode. And the music will automatically switch to GPS voice.

Besides, you can also gain great convenience and enjoyment by pairing your Bluetooth-enabled mobile phone with this all-in-one unit for Bluetooth hands-free phone calls and streaming music at the same time.

Wish you like this unit and good luck to you!

Posted in Uncategorized | Tagged | Leave a comment

The Straightforward Method to Upgrade a 2007 2008 2009 2010 2011-2014 TOYOTA Alphard Vellfire 350Z G Bluetooth DVD GPS Car Radio Effectively

To improve your car’s capabilities and performance, you may consider replacing your factory radio with a new multifunctional car radio which can bring you a lot of great convenience and enjoyment in your car. This article aims to introduce a 2007 2008 2009 2010 2011-2014 TOYOTA Alphard Vellfire 350Z G car radio installation guide from Seicane to you.If you own the same or similar dashboard, you can refer to this guide carefully to help with the installation.

2007 2008 2009 2010 2011-2014 TOYOTA Alphard Vellfire 350Z G Bluetooth DVD GPS Car Radio after installation

2007 2008 2009 2010 2011-2014 TOYOTA Alphard Vellfire 350Z G Bluetooth DVD GPS Car Radio after installation

Here are some tips about the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and www.seicane.com make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd- 400

2007 2008 2009 2010 2011-2014 TOYOTA Alphard Vellfire 350Z G car radio installation guide

1. Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside.

Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside

Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside

2. Remove screws that fixed the radio on the dashboard.

Remove screws that fixed the radio on the dashboard

Remove screws that fixed the radio on the dashboard

3. Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio.

Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio

Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio

4. Unplug the connectors at the back of the factory radio.

Unplug the connectors at the back of the factory radio

Unplug the connectors at the back of the factory radio

5. Make antennas and cables connected step by step, and you should be very careful when you are doing this for it will affect whole procedure.

Make antennas and cables connected step by step, and you should be very careful when you are doing this for it will affect whole procedure

Make antennas and cables connected step by step, and you should be very careful when you are doing this for it will affect whole procedure

6. Put the new Seicane head unit into your car, you should check whether your connections are correct, and you’d better have a tidy for the cables.

7. If everything is OK, firm screws into their original place.

If everything is OK, firm screws into their original place

If everything is OK, firm screws into their original place

8. Firm the panel on the new Seicane head unit. Finally the new Seicane head unit is installed and a comprehensive test should be conducted on the new head unit.

Firm the panel on the new Seicane head unit. Finally the new Seicane head unit is installed and a comprehensive test should be conducted on the new head unit

Firm the panel on the new Seicane head unit. Finally the new Seicane head unit is installed and a comprehensive test should be conducted on the new head unit

 

That’s all about how to remove and install a 2007 2008 2009 2010 2011-2014 TOYOTA Alphard Vellfire 350Z G car radio. If you encounter any problems and don’t know how to deal with, you can seek help from your dealer, someone experienced or a professional. Anyway, first of all, it is essential for you to pick an ideal car radio for your beloved car. If you don’t know which kind of car can radios can fit your car well,  you can check out the following link which is a smart 2007 2008 2009 2010 2011-2014 TOYOTA Alphard Vellfire 350Z G car radio from Seicane.

https://www.seicane.com/9-inch-android-gps-navigation-system-for-2007-2013-toyota-alphard-with-dvd-player-bluetooth-radio-mirror-link-multi-touch-screen-obd-dvr-rearview-camera-tv-usb-sd-3g-wifi-s169005

This all-in-one car radio is running on the latest and stable Android 7.1 operation system, a powerful quad-core CPU processor and 2GB RAM. So with it installed in your car, you are able to enjoy a much smoother, faster and easier operation experience.

Through turn-by-turn directions and voice prompts offered by the high-accuracy GPS navigation, you can easily and quickly know your current locations and have the suitable route option to reach your desired destinations. And thanks to this car radio’s dual zone function, you can also freely enjoy your favorite music under GPS mode, which won’t have any negative influence on GPS function.

What’s more, under the Bluetooth technology, you can connect your Bluetooth-enabled mobile phone to this unit so as to get access to both Bluetooth hands-free phone calls and Bluetooth streaming music. Therefore, you will have a more convenient and relaxing in-car life.

If you like this unit, just add it to your shopping cart. Good luck to you!

Posted in Uncategorized | Tagged | Leave a comment

Simple Tricks on a 2005 2006 2007 2008 2009-2010 Nissan PATHFINDER GPS Bluetooth DVD Car Radio Replacement

There is no doubt that an ideal car radio plays a very important role in a car since it can be compatible with a lot of problems to meet your different need and help you gain an unforgettable driving experience. If you are fed up with your factory radio, you can think about installing a brand new multifunctional car radio to replace your factory radio. The following is a    2005 2006 2007 2008 2009-2010 Nissan PATHFINDER car radio installation instruction from Seicane, which can be taken as your reference.

2005 2006 2007 2008 2009-2010 Nissan PATHFINDER     GPS Bluetooth DVD Car Radio after installation

2005 2006 2007 2008 2009-2010 Nissan PATHFINDER GPS Bluetooth DVD Car Radio after installation

Tips about the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2005 2006 2007 2008 2009-2010 Nissan PATHFINDER car radio installation instruction

1. Pry around the edges of the trim panel with removal tools.

Pry around the edges of the trim panel with removal tools

Pry around the edges of the trim panel with removal tools

2. Take the trim panel out of the dash.

Take the trim panel out of the dash

Take the trim panel out of the dash

3. Disconnect all the connectors at the back of the panel.

Disconnect all the connectors at the back of the panel

Disconnect all the connectors at the back of the panel

4. Unscrew all the screws holding the original car radio in place with a screwdriver.

Unscrew all the screws holding the original car radio in place with a screwdriver

Unscrew all the screws holding the original car radio in place with a screwdriver

5. Gently take the original car radio out of the dash.

6. Disconnect all connectors at the back of the original car radio.

7. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

8. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

9. Connect the Seicane car radio to your original car radio ‘s plugs.

10. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

11. Put the new Seicane car radio into the dash.

12. Put everything into their original place. All the installation is done.

 

Wish you can gain some help from the above installation instruction. If you meet any difficulties and don’t know how to overcome them, you can seek help from your dealer, someone experienced or a professional. For avoiding damage to either your car radio or your car, you’d better arrange a professional technician to help you install the new car radio.

Additionally, to help you select an ideal car radio, here I’d like to recommend a 2005 2006 2007 2008 2009-2010 Nissan PATHFINDER car radio from Seicane to you. For more details, please click:

https://www.seicane.com/android-touch-screen-radio-gps-navigation-system-for-2005-2010-nissan-pathfinder-with-bluetooth-dvd-player-mirror-link-obd2-rearview-camera-dvr-tv-3g-wifi-usb-sd-1080p-video-s166226

Loaded with the latest Android 7.1 operation system, a high-quality quad-core CPU processor and 2GB RAM, this remarkable car radio makes it possible for you to gain the great convenience and enjoyment in car to upgrade your in-car life.

With this car radio installed in your car, you can get access to a wide range of comprehensive features, mainly including 3D GPS navigation, DVD player, FM/AM radio tuner, Bluetooth hands-free phone calls, Bluetooth streaming music, AUX, file management, etc.

Apart from these basic features, there are also some optional features you can add to this unit according to your requirements or preference, such as car DVR, 3G module, OBD2, TPMS, etc.

Under the guidance of the turn-by-turn directions and voice prompts provided by the high-end 3D GPS navigation system, you are able to know your current locations and navigate to your desired destinations. And this car radio comes with dual zone function, which enables you to listen to your favorite music while navigating.

Wish you like this unit and good luck to you!

Posted in Uncategorized | Tagged | Leave a comment

The Direct Instruction on a 2007 2008 2009 2010-2011 Nissan SENTRA Car Stereo with DVD Player Bluetooth GPS Navigation System

As a car owner of a 2007 2008 2009 2010-2011 Nissan SENTRA, if your original car radio is not too advanced to be compatible with some upgraded or modern features, you may want to replace it with a brand new car radio. And with such an ideal car radio installed in your car, you can get access to comprehensive features to meet your various needs in car. While for the new car radio installation, if you have some related installation experience, you can refer to a related installation guide. The following is a 2007 2008 2009 2010-2011 Nissan SENTRA car radio installation guide from Seicane, which can be taken as your reference.

2007 2008 2009 2010-2011 Nissan SENTRA Car Stereo after installation

2007 2008 2009 2010-2011 Nissan SENTRA Car Stereo after installation

Some tips before the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2007 2008 2009 2010-2011 Nissan SENTRA car radio installation guide

1. Pry around the edges of the trim panel with removal tools.

Pry around the edges of the trim panel with removal tools

Pry around the edges of the trim panel with removal tools

2. Take the trim panel out of the dash.

Take the trim panel out of the dash

Take the trim panel out of the dash

3. Disconnect all the connectors at the back of the panel.

Disconnect all the connectors at the back of the panel

Disconnect all the connectors at the back of the panel

4. Unscrew all the screws holding the original car radio in place with a screwdriver.

Unscrew all the screws holding the original car radio in place with a screwdriver

Unscrew all the screws holding the original car radio in place with a screwdriver

5. Gently take the original car radio out of the dash.

6. Disconnect all connectors at the back of the original car radio.

7. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

8. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

9. Connect the Seicane car radio to your original car radio ‘s plugs.

10. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

11. Put the new Seicane car radio into the dash.

12. Put everything into their original place. All the installation is done.

 

If you cannot fully understand this installation guide, please don’t hesitate to consult your dealer, communicate with someone experienced or turn to a professional for help. If you still think it hard to finish the whole upgrade process, you can straightly arrange a professional technician to help you install the new car radio. But if you haven’t got a suitable car radio,I’d like to share a great car stereo from Seicane which is for a 2007 2008 2009 2010-2011 Nissan SENTRA. Here comes the related link, please click:

https://www.seicane.com/android-aftermarket-radio-gps-navigation-system-for-2007-2011-nissan-sentra-with-touch-screen-wifi-bluetooth-dvd-player-mirror-link-obd2-dvr-tv-3g-usb-sd-1080p-video-rearview-camera-s166226

This car radio is running on the latest and stable Android 7.1 operation system and a powerful quad-core CPU processor, this great car radio comes with a wide range of comprehensive features to meet your different needs in car.

Under the guidance of the turn-by-turn directions and voice prompts provide by the high-end 3D GPS navigation system of high accuracy, you are able to know your current navigation system and find the right way to get to your desired destinations. And this unit’s dual zone function enables you to listen to your favorite music while navigating.

Besides, under the wireless Bluetooth technology, you can pair your Bluetooth-enabled mobile phone with this car radio so as to get access to both Bluetooth hands-free phone calls and Bluetooth streaming music. Therefore, you can gain a lot of convenience and enjoyment.

Wish you like this unit and good luck to you!

Posted in Uncategorized | Tagged | Leave a comment